#Pentair screenlogic troubleshooting install#

Most contractors would have refused to install a product that they werenвЂ™t familiar with. My husband and I actually made their job harder, as we were interested in installing a special custom spa and waterfall that they had never worked with before. They made sure everything was done correct even if they had to take it all apart and do it again. What an awesome, HARDWORKING family! Every single member of SteveвЂ™s team is extremely respectful, caring, outgoing, responsive, and attentive. Once our pool permit went through, we met the rest of the Cronin Family, as his 4 sons (known as the boys) and his nephew, who actually installed the pool/spa. He walked us through everything we were buying and what the proвЂ™s and conвЂ™s were for each. Most only care about how much money they can make off of you - this is NOT the case with вЂMy Favorite Pool BuilderвЂ™. This is IMPOSSIBLE to find in ANY contractor these days. He will tell you the truth, regardless of whether or not it will affect him negatively. He is genuine, extremely professional, and flat out the real deal. Our favorite thing about Steve is that he is SO HONEST. He never asked us for any money to come out and help us вЂњplanвЂќ our dream pool. He made several more trips out and countless hours on the phone to help us with planning electrical and concrete slabs. However, our builder wanted to charge us a fortune (as a supervision fee) to add a pool to our home as it was being built, so we decided to wait until we closed.Д«efore we ever made a down payment, Steve came out (before the drywall was even installed in our home) and told us where to run the electrical and how many amps we are going to need for the pool and spa (this was a significant savings for us). Steve Cronin was with us from the very beginning My husband and I built a new construction home in Gainesville Florida and we knew that we wanted a fiberglass pool. I cannot say enough wonderful things about вЂMy Favorite Pool BuilderвЂ™. Make sure itвЂ™s enabled by going through the menu like weвЂ™ve been doing, check your speed instead of flow. So far thermal mode set from the factory, you just want to check to make sure itвЂ™s correct and that itвЂ™s on. Priming I just lower the speed that it primes at so itвЂ™s not revving up so high. If it was in schedule it would switch to the timed schedule. Then after that, it would shut off if itвЂ™s not in schedule. ItвЂ™s used to clean the pool when youвЂ™re out of schedule for example you had a party in the middle of the night and then whenever youвЂ™re done and you want to start the pool cleaning you would hit quick clean and run through the 10 hour program. Quick clean set up is just like everything else in the system you have to select it, set your speed set your time, and normally set it for 10 hours at the high speed setting of the pump in 2500 2350. I normally hit the stop-start and turn the pump off, the danger of that though is its if you forget to turn the pump back on now itвЂ™s not going to run at schedule. So this allows the technician to clean the pool filter. Timeout used in the feature section to make it where you can actually shut the pump down for predetermined time say 15 minutes half hour or hour. Thermal Motors and features and weвЂ™re going to go through features kind of quick because itвЂ™s basically works the same way as everything else, just toggling up and down and making the changes that you need to make, an end of each individual section Keep in mind this pool is just being set up to run temporarily for now just for this demonstration, also the water is in the 40-degree mark where right now it doesnвЂ™t really need to run as much. We are setting our shut down time for 11:01 a.m. the overlap will allow whichever pump speed is higher speed to run for that one minute just to avoid the pump trying to shut down and restart quickly. You would go through the schedule, down to speed, change your speed if you need to in the speed section, select that then you get to the start time with your starting at 7 a.m. The only thing I want to show you is that this one thing about time overlap. You would do everything the same way as we did in five. Program six is the same as five also 7 at 8. on this pump and we set it to run from 6 a.m. once you set your shut off time you hit save back get to the main menu by hitting back, turn the power off, turn it back on.